- #ELEXA CONSUMER PRODUCTS LEVEL MOUNT INSTALL#
- #ELEXA CONSUMER PRODUCTS LEVEL MOUNT FULL#
- #ELEXA CONSUMER PRODUCTS LEVEL MOUNT TV#
Plasma/LCDs TVs with a flat back panel will require a shorter bolt. Laying the television down on the glass may cause permanent damage.
NOTE: NEVER LAY YOUR TELEVISION FACE DOWN ON ITS GLASS.
#ELEXA CONSUMER PRODUCTS LEVEL MOUNT TV#
Attaching Mounting Arms to a TV with a Flat Back.2 M5 bolts must be used per Extension Arm. The multiple hole pattern on the Extension Arms make it easy to adjust to fit your unique televisionĪttach the Extension Arms to the Tilt Arms by threading the M5 bolts into the provided Lock Washer, through the Extension Arm, through the Tilt Arms and tighten with the provided Hex Nut. It is recommended to measure the distance between the mounting holes on the back of your TV prior to attaching the Extension Arms. If you need to use the Extension Arms, you must use all Extensions Arms in order for the Mount to properly hold your TV. If you have an oversized Flat Panel TV, you may need to use the Extension Arms provided. NOTE: You will not use all of the hardware included. Thread the bolts carefully into your Flat Panel by hand to determine which provided mount hardware (correct diameter) is appropriate for installation.ĬAUTION: If you feel resistance, remove the bolt immediately and try another size! Next determine the correct length of the required bolt as described in the step 7. Select bolts from Bags 1-4, which most resemble the holes in the back of your Flat Panel. Selecting the Appropriate Hardware for your Flat Panel.Drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate, then proceed to drive the remaining 6 screws into the concrete anchors. Do not screw too tight until all the screws are in. Once the Wall Plate is in the correct position on the wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer in the upper left mounting hole of the Wall Plate. Insert all anchors into the holes and set them flush to the wall by tapping them in with a hammer. Drill into the wall at least as deep as the screw is long (3 inches). Drill holes for the concrete anchors using an electric drill with a masonry bit (1/2’’ or 12mm). Utilize the built-in bubble level to ensure proper mounting.
Mark the eight holes you will be using for concrete anchors.
#ELEXA CONSUMER PRODUCTS LEVEL MOUNT INSTALL#
Place the Wall Plate at the height you want to install the Flat Panel wall Mount. NOTE: Due to the weight of the LCD/Plasma TV’s, it is necessary to mount the Wall Plate to at least 2 studs. Now tighten both screws, proceed to drive the remaining 6 screws into the studs.Īll hex screws will require 1/8 inch pilot holes. Using the Bubble Level as your guide, drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate. Do not screw too tight until after all the screws are in. Once the Wall Plate is in the correct position on the studs, screw 1 Hex Screw and 1 Hex Washer into the upper left mounting hole of the Wall Plate into the stud. Images of wall plate are shown for clarity of screw locations. If you are attaching the mount to concrete please skip to step 4.Ĭaution: Do not disassemble mount. The tilt arms will adjust horizontally to the right and left up to 8 inches after you determine the desired viewing location. The mount requires a minimum of two studs to ensure proper and safe installation. It is recommended that the center of the stud be used – and that a nail be used to verify that a stud has been located. Locate a proper place to mount by using a quality stud finder.
#ELEXA CONSUMER PRODUCTS LEVEL MOUNT FULL#
Make sure all screws and bolts are tightened before allowing Wall Mount to bear the full weight of the LCD Display. DO NOT MOUNT ONLY TO DRYWALL.īefore installing, check to make sure all parts of the mount are included. THE MOUNT MUST BE ATTACHED TO WOOD STUDS OR TO PROPERLY INSTALLED ANCHORS IN CONCRETE. It is the responsibility of the installer to verify that the mount is anchored properly to the wall. Installer must make sure the LCD Wall Mount is properly and securely attached and that appropriate fasteners are used. Please also visit our Web Site at for assistance. Our trained Customer Service Department is open 24 hours a day, 7 days a week, every day of the year and is prepared to assist you in both English and Spanish.
IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY, LEVEL MOUNT, DIRECTLY.ĭial 1 8 or email us at any time of the day or night for a quick and efficient solution to your problem. Level Mount Large and Extra Large Flat Panel Full Motion Cantilever Wall Mount InstructionsĭO NOT RETURN THIS PRODUCT TO THE STORE OR WEB SITE YOU PURCHASED FROM! See Flash demo for product images and multimedia.
0 kommentar(er)
